Table Saw

How to Reset Overload on Table Saw?

How to Reset Overload on Table Saw
Written by Muhammad Haseeb

There are a few things you can do to fix an overload on your table saw. One of the main problems that can happen when using a table saw is that it gets too heavy. It happens when the saw gets too hot because the blade and the thing being cut are rubbing against each other too much.

A table saw that is too full of work is a worry that can stop your work in its tracks. When a table saw overloads, it can be a bother, but with this troubleshooting help on how to reset overload on table saw, you should be able to fix it quickly and get back to work.

How to Reset Overload on Table Saw: Step-by-Step Instructions

How to Reset Overload on Table Saw
How to Reset Overload on Table Saw

If your table saw has ever stopped working because it was too busy, don’t worry. This happens a lot, and it’s not hard to fix. We’ll show you how to reset the overload on a table saw in the steps below.

  • Turn off the table saw and remove it from the electrical outlet.
  • Find the button that resets the overload. Most of the time, the reset button is red and is on the side or back of the table saw near the motor.
  • Use a brush or compressed air to clean the area around the button.
  • Press and keep holding the reset button for about 3 to 5 seconds.
  • After you have done the fix, plug the table saw back into the wall and turn it on.
  • If the table saw still won’t turn on after being restarted, go back and do the steps again.
  • If the table saw still won’t start, check to see if the blade is broken. If the blade is broken, you should get a new one.
  • Put the blade back on and make sure it is tight.
  • Plug the table saw back into the wall to turn it back on.
  • The problem can’t be fixed by turning off and restarting the table saw. There may be a more serious problem with the motor, so you should call a service person.

Get Help from a Pro:

If you’re not sure you can safely reset the motor overload on your table saw, or if the problem still happens even after you reset the switch, you should call a pro. 

A trained technician will know how to use the ohm meter to check for voltage drops and other technical problems in the right way. A pro will fix any problems with your saw and make sure it’s safe to use.

Also, it can be dangerous to try to fix a table saw on your own. Table saws have strong motors and sharp blades, so if you don’t know what you’re doing, you could hurt yourself or damage the saw.

If you need help turning off the overload on your table or saw, or if the problem keeps happening, you should call an electrician.

How and Why did your Table Saw Get Stuck?

How and Why did your Table Saw Get Stuck?

If you’ve ever tried to turn on your table saw only to find that the blade won’t move, you know how frustrating it can be. A table saw is a powerful tool that can make quick work of a wide range of woodworking jobs. 

As with any tool, there can be problems from time to time. One problem you might run into is that your table saw stops working all of a sudden.

Every maker needs a table saw, so when it stops working right, it’s important to find out what’s wrong as soon as possible.

We’ll talk about and look at some of the most common reasons why you might be stuck, as well as a few ways to fix the problem so you can get back to work.

Look at the Blade:

When a table saw blade won’t turn, one of the most common reasons is that the blade is dull or broken. Check the edge of the blade to see if it has any nicks or chips. If so, you’ll need to change the blade before going any further.

Check for Blockages:

There’s also a chance that something is stuck in the blade, stopping it from turning. Carefully clean up any dirt you find, and then try again to turn on the saw.

Check the Engine:

If neither of these ways of restarting the table saws overload works, it’s likely that something is wrong with the motor itself. The best way to figure out what’s wrong is to take the table saw to someone who knows how to fix it and have them look at it.

Change out the Capacitor:

Your table saw can get stuck and overloaded if the capacitor is broken. If you think this is the problem, try turning off the power and taking out the old capacitor before turning on your table saw again. After you’ve replaced it, try turning the saw back on or doing a table saw restart.

Clean the Points of Binding:

Dust can build up in the binding points over time, making your table saw bind and stop working. Before you try to reset the overloaded table saw, you can also try to fix this problem by simply cleaning out the binding points with a toothbrush or compressed air and then trying to use the saw again.

Check for Energy:

If your table saw stops working, one thing you should do is make sure it’s plugged in and that the outlet has power. If the saw is plugged in but still doesn’t work, you may need to reset the circuit breaker or change a blown fuse.

Examine the Blade:

Another reason why your table saw might not work is if the blade is broken or worn down. If the blade is broken, you will have to get a new one. If it’s just dull, you can sharpen it yourself or get it sharpened by an expert.

Clean out the Gun Port:

If your table saw has a brushless motor, the weapon port might need to be cleaned. Over time, dust builds up in this area, which stops the motor from working right and causes it to overheat and break.

Instead of just putting your table back together, try cleaning it first. Just take off the screws that hold the cover in place and use a brush or compressed air to clean out any dirt that has built up inside.

Look for Safety Problems:

Before you start fixing other problems, you should make sure there are no safety problems that need to be fixed. For example, your saw might not be working because the blade guard isn’t in place or isn’t working right.

 In the end, you should never try to fix your table saw unless you are certain that it is safe to do so.

Firmware Upgrades:

Lastly, if you still can’t get your table saw unstuck, it could be because of a problem with the software. Check your owner’s guidebook or the manufacturer’s website to see if there are any new versions.

How to Troubleshoot a Table Saw Overload?

How to Troubleshoot a Table Saw Overload

There are many reasons why the table saws are too heavy. Most of the time, it’s because the blade is dull and needs to be changed. If the blade is dull, it won’t be able to cut through the material as quickly and will make the material harder to cut through.

First Possible Reason:

If the material you are trying to cut is too thick, it can also cause an overload. The thickness of the material can also make it harder to cut through and cause the blade to get too hot, which can cause the table saw to overload. Damaged teeth on the blade can also make the motor work harder and cause it to overload.

Second  Possible Reason:

If you think the table saw is overloading because of the blade, the first thing you should do is check the blade for damage. They might need to be changed. If any of the teeth are getting worse. If the blade is just dull, you can replace it or sharpen it yourself.

Third Possible Reason:

If you don’t think the blade is the problem, it’s likely that the material you’re trying to cut needs a thick and sharp table saw blade. In this case, you’ll need to use a different type of saw that works better with thicker materials. When you check your saw blade or change it, be sure to follow all safety rules.

Common Mistakes To Avoid When Resetting Your Table Saw’s Overload:

  • Trying to turn off the excess without fixing the problem
  • Leaving the saw plugged in while restarting the overload
  • When you press the excess button or switch with the wrong tool,
  • Not following the directions from the manufacturer on how to reset the overload

Safety Guidelines for Resetting the Overload on Your Table Saw:

  • Wear safety glasses every time you use a table saw.
  • Make sure the blade is completely still before you try to restart the overload.
  • Before you try to fix the overload, unplug the saw.
  • Do not try to reset overload unless you are sure the problem has been fixed.

Bottom Line:

Table saws are very useful tools for woodworkers of all skill levels, but only if they work right. Don’t worry if your table saw gets stuck. Even if you take good care of your tools, sometimes all they need is a little love and care to get back up and going.

There are a number of things that could be done to get it back up and running quickly. By using the fixing tips above, you should be able to get your trusted table saw back up and running in no time.

Nevertheless, you now know when it is time to call in reinforcements. Thanks for reading.


How do you get an Overload Relay to Work Again?

Here are the steps you need to take to reset an overload relay:

  • Find the relay, which is a small box with connections for the power source and the load. The relay could be close to the motor of the table saw or in a control box.
  • Turn off the appliance’s power.
  • Take the load off the relay.
  • Press the reset button or, if the relay has one, flip the reset switch to turn the relay back on.
  • Put the load back on the relay.
  • Turn the appliance’s power back on.

What Causes My Table Saw to Overload?

The overload on your table saw could be caused by a few different things. Most of the time, an overload trip happens because the blade is stuck. When the blade gets stuck, it puts too much pressure on the motor, which trips the overload.

The saw being too heavy is another common cause of an overload trip. This can happen when you try to cut through a piece of wood that is very thick. As a safety step, if the saw is too heavy, it will turn off.

How Can I Prevent My Table Saw from Being Overloaded?

To avoid overloading your table saw, use the appropriate blade and feed rate for the task, keep your saw clean and well-maintained, and inspect it for damaged or deteriorated parts that could cause it to work harder than necessary.

Related Posts:

About the author

Muhammad Haseeb

Muhammad Haseeb is the CEO and Founder of Techy Saw, a website that provides reviews, tutorials, and information about cutting saws. He studied at Concordia College and Virtual University of Pakistan. Haseeb has over 5 years of experience in the woodcutting industry.

Leave a Comment